U.S. hadn't updated crib safety standards for 30 years

By James R. Hood of ConsumerAffairs

Setting aside objections from retailers and manufacturers, the U.S. Consumer Product Safety Commission is implementing new safety standards for baby cribs later this month.

Effective June 28, anyone who manufactures or sells cribs will be required to meet the new standards, although day care centers, crib rental companies and hotels will have until December 28, 2012 to update their cribs.

“I am very pleased that the new mandatory crib standards will stop the manufacture and sale of dangerous traditional drop-side cribs and will vastly improve the structural integrity of cribs,” said CPSC chair Inez M. Tenenbaum, noting that crib safety standards have not been updated in nearly 30 years.

Detaching drop-side rails were associated with at least 32 infant suffocation and strangulation deaths since 2000, according to the CPSC. Additional deaths have occurred due to faulty or defective hardware.

Manufacturers and retailers had objected that the new rules would cause an economic hardship, particularly on smaller stores but the commission voted 3-2 to impose the new standards on schedule.

The new standards will:

1. stop the manufacture and sale of dangerous, traditional drop-side cribs;

2. make mattress supports stronger;

3. improve slat strength,

4. make crib hardware more durable; and

5. make safety testing more rigorous.

The standards aim to keep children safer in their cribs and prevent deaths resulting from detaching crib drop-sides and faulty or defective hardware. The tougher standards were mandated by the Consumer Product Safety Improvement Act of 2008.

Tenenbaum said the commission granted the delays to child care centers, crib rental stores and hotels and motels were necessary not only to minimize the economic impact but also to prevent shortages of new cribs. She estimated that replacing all of the cribs already in use at such locations would create a demand of approximately 935,000 cribs, which would amount to nearly $467 million in replacement costs.

“In order to ensure sufficient availability of compliant cribs and ensure an orderly and successful transition to the use of complaint cribs by child care providers and places of public accommodation, the Commission adopted a two-step phase in of the rule,” Tenenbaum said.

Retailers unhappy

Any cribs not meeting the current standard must be destroyed if they’re not sold by June 28. Industry estimates put the number of unsold cribs between 10,000 and 20,000. Some retailers, hoping to clear out their stock, have offered steep discounts to consumers.

“Overregulation is going to lead to the destroying of thousands of cribs that are perfectly good — many that are better than what will come out after the new regulations,” Gene Francis, a South Dakota-based retailer and member of the National Independent Nursery Furniture Retailers Association, told Kids Today.

But Commissioner Thomas Moore showed little sympathy for that argument.

"We expect companies to comply with the Commission’s rules," he said. "It appears that the vast majority of retailers did plan and are ready to comply by the June 28th date.  In a rule of this magnitude, it is expected that there will be 
some market disruption and that some companies will experience economic loss."

Moore said it was impractical to ask the CPSC to allow retailers to continue selling cribs that do not meet the new standard.

"There is little that we know about the noncomplying cribs these retailers want to sell or about the reasons the retailers find themselves with noncompliant inventory.  However, there is much that we don’t know.  When were these cribs made?  Who made them and where?  Who tested them and when?  What standard were they tested to?  When were they ordered?  Did the quantity ordered take into account the looming effective date of the new crib standards?"

"Were retailers buying imported noncomplying cribs at fire sale prices to try to make a profit before they had to start buying more expensive cribs that met the new standards?" Moore asked.  "Will retrofit kits be available to bring the cribs into compliance?  We simply do not know."

The crib's tubular metal mattress-support frame can bend or detach and cause part of the mattress to collapse, creating a space into which an infant or toddler can roll and become wedged, entrapped or fall out of the crib.

          









      

CPSC has received a report of a one-year-old child from North Attleboro, Mass. who suffocated when he became entrapped between the crib mattress and the crib frame in April 2008. CPSC is aware of 13 additional incidents involving the recalled cribs collapsing due to the metal mattress-support frame bending or detaching, including one child entrapment that did not result in injury, and one child who suffered minor cuts to his head when his mattress collapsed and he fell out of the crib.

CPSC staff urges parents and caregivers to stop using these cribs immediately and find an alternative, safe sleeping environment for their baby. Do not attempt to fix these cribs.

Due to the fact that Simplicity and its successor, SFCA Inc., are no longer in business, CPSC has limited information about the number of cribs sold.

All Simplicity drop-side cribs have previously been recalled for a hazard involving the drop side. Simplicity drop-side cribs could still be in use by parents or caregivers who are unaware of the recalls or by those who received a repair kit to immobilize the drop side from Simplicity when the firm was still in business. This recall involves all Simplicity cribs with tubular metal mattress-support frames, which include but are not limited to the following models:

Some model numbers are followed by letters, indicating the color or finish of the crib. The name "Simplicity Inc." or "Simplicity for Children" appears on a label on the crib's mattress-support frame and/or the crib's end panels. The cribs were manufactured in China.

The recalled cribs were sold at Walmart, Target, Babies R Us and other stores nationwide for between $150 and $300. Consumers should contact the store where the crib was purchased to receive a refund, replacement crib or store credit.

Warning

CPSC would like to remind parents not to use any crib with missing, broken or loose parts. Make sure to tighten hardware from time to time to keep the crib sturdy. When using a drop-side crib, parents should check to make sure the drop side or any other moving part operates smoothly. Always check all sides and corners of the crib for disengagement. Any disengagement can create a gap, which could fatally entrap a child. In addition, do not try to repair any side of the crib with tape, wire, rope or by other means. Infants and toddlers have died in cribs with makeshift repairs.

For more information on Crib Safety, visit CPSC's Crib Information Center.

The recall is being conducted in cooperation with the U.S. Consumer Product Safety Commission (CPSC).

Could crib bumpers be one step closer to being banned?

Crib bumpers, the pillow-like lining used to separate the sides of the crib with an infant’s head, may be one step closer to extinction due to beefed up safety guidelines by the U.S. Consumer Product Safety Commission (CPSC).

While the CPSC doesn't specifically discourage use of bumpers, it does recommend keeping all extraneous items out of cribs like stuffed animals, pillows and heavy quilts.

Plus, whether it was intended or not, bumpers are nowhere to be seen among the examples of safe cribs featured in the commission’s informational video online.

Crib bumper safety

The safety of crib bumpers has been a hotly debated topic over the last decade. Consumer advocacy groups and children’s safety organizations believe bumpers can cause suffocation, strangulation, or contribute to Sudden Infant Death Syndrome (SIDS).  However, the government has been slow to take a stand on the controversial crib accessory.

Still, the commission is not ignoring the subject of safe sleep areas for infants and young toddlers.

In December 2010, it unanimously approved new, stricter safety standards for all cribs; standards that had not been updated in thirty years.

Under the new guidelines, crib manufacturers must ensure mattress supports are stronger, the crib hardware is more durable, and the safety testing of their products is more rigorous.

The commission’s standards also stop the manufacture and sale of traditional drop-side cribs, which they warned parents about in May, 2010 and issued almost a dozen recalls for since 2005.

According to the commission, over seven million drop-side cribs were included in the recalls due to suffocation and strangulation hazards created by the drop side.

While these are steps in a positive direction, when (or if) the commission will address the possible safety hazards of crib bumpers is anyone’s guess.

Bumper ban

Illinois Attorney General Lisa Madigan has been calling for the end of crib bumpers since December 2010.

Last month, she urged the Juvenile Products Manufacturers Association (JPMA), the national industry trade group overseeing manufacturers of crib bumpers, to release the results of a study it conducted on the safety of bumpers.  As of mid-January 2011, the results have yet to be released.

Madigan continues to warn parents and care-givers of the potentially fatal risk of using crib bumpers.

Along with discouraging keeping bulky items out of cribs, the CPSC’s safety guidelines included other important tips to keep babies and young toddlers safe while they sleep:

• To prevent suffocation, never place pillows or thick quilts in a baby's sleep environment. Also, make sure there are no gaps larger than two fingers between the sides of the crib and the mattress.
• Proper assembly of cribs is paramount - Follow the instructions provided and make sure that every part is installed correctly. If you are not sure, call the manufacturer for assistance.
• Do not use cribs older than 10 years or broken or modified cribs. Infants can strangle to death if their bodies pass through gaps between loose components or broken slats while their heads remain entrapped.
• Set up play yards properly according to manufacturers' directions. Only use the mattress pad provided with the play yard; do not add extra padding.
• Never place a crib near a window with blind, curtain cords or baby monitor cords; babies can strangle on cords.

The commission also has resources for parents and care-givers to see if their child’s crib has been included in any of the recalls.

The cribs pose risks of strangulation, suffocation hardware linked to deaths and injuries

By James Limbach of ConsumerAffairs

The U.S. Consumer Product Safety Commission (CPSC) is warning consumers that "SafetyCraft" brand full-size and portable drop-side cribs manufactured or distributed by Generation 2 Worldwide contain drop-side hardware that appears to be identical to Generation 2 Worldwide ChildESIGNS brand drop-side cribs recalled in February 2010.

This hardware found on SafetyCraft drop-side cribs can fail and place infants and toddlers at risk of strangulation and suffocation. CPSC staff urges parents and caregivers to stop using these cribs immediately and find an alternative, safe sleeping environment for their baby. Do not attempt to fix these cribs.

Ownership change

Generation 2 Worldwide ceased operations in 2005. The "SafetyCraft" trademark was then purchased by Foundations Children's Products of Medina, OH. SafetyCraft cribs manufactured and sold by Foundations Children's Products are NOT the subject of this safety alert. Consumers can identify the Foundations SafetyCraft crib with "Foundations" printed on the mattress support assembly instructions label under the crib mattress.

Because Generation 2 Worldwide ceased operations, CPSC has limited information about these cribs and where they were sold. CPSC has been unable to identify major retailers that sold these cribs.

Identifying products

The name "SafetyCraft" appears on a label affixed to the crib's headboard or footboard. Product labels may identify the place of manufacture as Indonesia or Dothan, Alabama.

This warning involves all SafetyCraft drop-side cribs, including model 92-8112, manufactured and/or sold by Generation 2Worldwide. Some of the cribs have a clear plastic headboard and footboard. These cribs are in use in child care facilities as well as homes.

Danger to children

The crib's plastic drop-side hardware can break, which can cause the drop side of the crib to detach from a corner of the crib. When the drop side detaches, it creates a space into which an infant or toddler can roll and become wedged or entrapped.

When a child is trapped between the drop side and the crib mattress, it creates a risk of suffocation or strangulation. In addition, the crib's mattress support can detach from the crib frame, creating a hazardous space in which an infant or toddler can become entrapped and suffocate or strangle.

CPSC received reports of three infant suffocation deaths and 20 drop side-related incidents involving previously recalled models of Generation 2 Worldwide and ChildESIGNS cribs with plastic hardware similar to "SafetyCraft" cribs.

Parent advice

CPSC reminds parents not to use any crib with missing, broken, or loose parts. Make sure to tighten hardware from time to time to keep the crib sturdy. When using a drop-side crib, parents should check to make sure the drop-side or any other moving part operates smoothly.

Always check all sides and corners of the crib for disengagement. Any disengagement can create a gap and entrap a child. In addition, do not try to repair any side of the crib, especially with tape, wire or rope.

More information on crib safety can be found at CPSC's Crib Information Center.

Incident or injury reports that are either directly related to this product recall or involve a different hazard with the same product can be made here.

Missing Safety Pegs Create Risk of Entrapment and Suffocation

By Truman Lewis of ConsumerAffairs

The U.S. Consumer Product Safety Commission (CPSC) is repeating the 2008 recall of more than 985,000 drop-side cribs with "Crib Trigger Lock and Safety Peg" hardware.

In January 2011, CPSC and Delta Enterprise Corp., the crib's manufacturer, learned of a 2009 death in which a 7-month-old girl from Colorado Springs, Colo., became entrapped and suffocated between the detached drop-side and mattress of her recalled crib. The crib was purchased secondhand and re-assembled without safety pegs in the bottom tracks.

Missing safety pegs can create a situation where the crib's drop-side rail disengages from the track. This can create a hazardous space in which an infant can become entrapped and suffocate.

At the time of the October 2008 recall, CPSC notified consumers about the death of an 8-month-old girl who became entrapped and suffocated when the drop side of the crib detached. The crib involved in this incident also was re-assembled without safety pegs. At the time of the October 2008 recall announcement, there were reports of two entrapments and nine detachments in cribs without safety pegs.

"Buying or accepting cribs second hand can be risky," said CPSC Chairman Inez Tenenbaum. "Second hand cribs may not come with all of the necessary parts that are needed to make sure your baby is safe. We urge parents and caregivers to use caution and to be aware that new rules established by CPSC will bring safer cribs to the market this summer."

The repeated recall involves cribs that were made in Taiwan and Indonesia. The cribs were sold at major retail stores including Kmart, Target and Walmart between January 1995 and December 2005 (through September 2007 for model 4624) for about $100.

Delta's name and address is printed on the mattress support boards and the Delta logo is on the crib's top teether rail. Model numbers are located on the top of the mattress support board. This announcement includes the following 49 crib models with "Crib Trigger Lock with Safety Peg" drop-side hardware:

• 4320, 4340;
• 4500, 4520, 4530, 4532, 4540, 4542, 4550, 4551, 4580;
• 4600, 4620, 4624 - production dates 01/06 thru 11/07, 4640, 4660, 4720, 4735, 4742, 4750 - production dates 01/95 thru 12/00;
• 4760, 4770, 4780, 4790;
• 4820, 4840, 4850, 4860, 4880, 4890, 4892; and
• 4900, 4910, 4920, 4925-2, 4925-6, 4930, 4940, 4943, 4944, 4947, 4948, 4949, 4950, 4958, 4963, 4968, 4969, 4980.

CPSC urges parents and caregivers to immediately stop using cribs that are missing a safety peg on either leg of the drop side and contact Delta to receive a free, easy-to-install repair kit. Call Delta toll-free at (800) 816-5304 anytime or visit the firm's website at www.cribrecallcenter.com to order the free repair kit.

Parents and caregivers are encouraged to find a safe, alternative sleep environment for their child until the repair kit, with new safety pegs, is safely installed on the recalled cribs.

CPSC reminds parents not to use any crib with missing, broken or loose parts. Make sure to tighten hardware from time to time to keep the crib sturdy. When using a drop-side crib, parents should check to make sure the drop side or any other moving part operates smoothly. Always check all sides and corners of the crib for parts separating that can create a gap and entrap a child.

In addition, do not try to repair any side of the crib. Babies have died in cribs where repairs were attempted by caregivers. Crib age is a factor in safety. At a minimum, CPSC staff recommends that you do not use a crib that is older than 10 years old. New, mandatory federal crib rules take effect on June 28, 2011. All cribs manufactured and sold after that date must meet new and improved safety requirements. Older cribs do not meet the new standard and can have a variety of safety problems.

U.S. hadn't updated crib safety standards for 30 years

By James R. Hood of ConsumerAffairs

Setting aside objections from retailers and manufacturers, the U.S. Consumer Product Safety Commission is implementing new safety standards for baby cribs later this month.

Effective June 28, anyone who manufactures or sells cribs will be required to meet the new standards, although day care centers, crib rental companies and hotels will have until December 28, 2012 to update their cribs.

“I am very pleased that the new mandatory crib standards will stop the manufacture and sale of dangerous traditional drop-side cribs and will vastly improve the structural integrity of cribs,” said CPSC chair Inez M. Tenenbaum, noting that crib safety standards have not been updated in nearly 30 years.

Detaching drop-side rails were associated with at least 32 infant suffocation and strangulation deaths since 2000, according to the CPSC. Additional deaths have occurred due to faulty or defective hardware.

Manufacturers and retailers had objected that the new rules would cause an economic hardship, particularly on smaller stores but the commission voted 3-2 to impose the new standards on schedule.

The new standards will:

1. stop the manufacture and sale of dangerous, traditional drop-side cribs;

2. make mattress supports stronger;

3. improve slat strength,

4. make crib hardware more durable; and

5. make safety testing more rigorous.

The standards aim to keep children safer in their cribs and prevent deaths resulting from detaching crib drop-sides and faulty or defective hardware. The tougher standards were mandated by the Consumer Product Safety Improvement Act of 2008.

Tenenbaum said the commission granted the delays to child care centers, crib rental stores and hotels and motels were necessary not only to minimize the economic impact but also to prevent shortages of new cribs. She estimated that replacing all of the cribs already in use at such locations would create a demand of approximately 935,000 cribs, which would amount to nearly $467 million in replacement costs.

“In order to ensure sufficient availability of compliant cribs and ensure an orderly and successful transition to the use of complaint cribs by child care providers and places of public accommodation, the Commission adopted a two-step phase in of the rule,” Tenenbaum said.

Retailers unhappy

Any cribs not meeting the current standard must be destroyed if they’re not sold by June 28. Industry estimates put the number of unsold cribs between 10,000 and 20,000. Some retailers, hoping to clear out their stock, have offered steep discounts to consumers.

“Overregulation is going to lead to the destroying of thousands of cribs that are perfectly good — many that are better than what will come out after the new regulations,” Gene Francis, a South Dakota-based retailer and member of the National Independent Nursery Furniture Retailers Association, told Kids Today.

But Commissioner Thomas Moore showed little sympathy for that argument.

"We expect companies to comply with the Commission’s rules," he said. "It appears that the vast majority of retailers did plan and are ready to comply by the June 28th date.  In a rule of this magnitude, it is expected that there will be 
some market disruption and that some companies will experience economic loss."

Moore said it was impractical to ask the CPSC to allow retailers to continue selling cribs that do not meet the new standard.

"There is little that we know about the noncomplying cribs these retailers want to sell or about the reasons the retailers find themselves with noncompliant inventory.  However, there is much that we don’t know.  When were these cribs made?  Who made them and where?  Who tested them and when?  What standard were they tested to?  When were they ordered?  Did the quantity ordered take into account the looming effective date of the new crib standards?"

"Were retailers buying imported noncomplying cribs at fire sale prices to try to make a profit before they had to start buying more expensive cribs that met the new standards?" Moore asked.  "Will retrofit kits be available to bring the cribs into compliance?  We simply do not know."

July 2, 2009
About 400,000 Simplicity drop side cribs are being recalled. The crib's plastic hardware can break or deform, causing the drop side to detach. When the drop side detaches, it creates space between the drop side and the crib mattress. Infants and toddlers can roll into this space and become entrapped which can lead to suffocation.

Federal safety regulators say they are aware of one death involving an 8-month-old child from Houston, Texas who became entrapped and suffocated between the drop side and the crib mattress when a plastic connector on the drop side broke. CPSC also is aware of an additional 25 incidents involving the drop side detaching from the crib.

In six of these incidents, the drop side detached because the plastic flexible tab deformed or broke. In four of the drop side detachment incidents, other plastic parts, including connectors or tracks, deformed or broke. In two of the incidents, two children became entrapped between the drop side and the crib mattress. There were no reported injuries.

The cribs were imported by Simplicity Inc. and SFCA Inc. of Reading, Pa. The firms are apparently no longer in business and unable to aid in the recall, the CPSC said.

This recall involves all drop side cribs with a different or 'newer' style of plastic hardware from those cribs recalled in September 2007. This newer style of Simplicity hardware can be identified by a flexible plastic tab at the top of the lower tracks. The recalled model numbers include but may not be limited to: 8050, 8325, 8620, 8745, 8748, 8755, 8756, 8765, 8778, 8810, and 8994, 8995, 8996.

The cribs, made in China, were sold at department stores, children's stores, and mass merchandisers nationwide from January 2005 through June 2009 for between $150 and $300.

Consumers should immediately stop using the recalled cribs and find an alternative, safe sleeping environment for their baby. Consumers should immediately return the crib to the place of purchase for a refund, replacement or store credit.

The recall is being conducted in cooperation with the U.S. Consumer Product Safety Commission (CPSC).

More than 9 million dangerous cribs recalled since 2005

By Mark Huffman of ConsumerAffairs

After high-profile recalls of drop-side cribs that can suffocate infants, the Consumer Product Safety Commission has expanded its recall to include two million cribs made by seven companies.

The beds included in the recall were made by Child Craft, Delta Enterprises Corp., Evenflo, Jardine Enterprises, LaJobi, More on this recall and Simmons Juvenile Products Inc.

Some, but not all, are the drop-side cribs, which pose a danger to infants who become trapped in the gap between the mattress and the side of the crib. Included in this latest recall is the Child Craft brand "Crib 'N' Double Bed" full size stationary-side crib with dowel.

The crib's stationary side can be assembled upside-down but still appears to be assembled correctly. If assembled upside-down, the crib side contains a hazardous five-inch gap at the top of the crib. Infants or toddlers can become entrapped in this gap, which can lead to entrapment, strangulation or other injuries.

CPSC has received four reports of children becoming entrapped between the dowel and the crib's stationary front side. In two of those reports, the child was trapped by his/her head and was in danger of being strangled. In the other two reports, the child was trapped by his/her arm. This hazard can occur on both the front and back sides of the crib, the agency said.

Listed below are cribs included in the latest recall.

747,000 Delta drop-side cribs

Improper installation can cause the mattress platform to collapse.

This recall involves Delta drop-side cribs with three different types of drop-side hardware and Delta cribs with wooden stabilizer bars that support the mattress platform.

• Delta Enterprises Corp.

750,000 Jenny Lind drop-side cribs distributed by Evenflo

CPSC and Evenflo have received 31 reports of drop sides that malfunctioned or detached. One involved the entrapment of a seven-month-old boy between the drop side and the crib mattress. He sustained bumps and bruises to his head. Nine children fell out of the crib when the drop side detached, unlocked or fell off. Seven of those children sustained minor injuries, including bumps, bruises and cuts. Fourteen other incidents involved no injuries. In addition, CPSC has received two reports of children who became entrapped when the mattress support detached in one corner of cribs manufactured between 2000 and 2004.

• More on this recall

306,000 Bonavita, Babi Italia and ISSI drop-side cribs manufactured by LaJobi

This recall involves all models of Bonavita, Babi Italia and ISSI drop-side cribs manufactured by LaJobi. The cribs have drop-side hardware that contains metal or plastic pegs that are recessed into either the drop side or the headboard and footboard of the crib. A label on the headboard of the crib identifies the manufacturer as LaJobi.

• LaJobi

130,000 Jardine drop-side cribs imported by Toys R Us

The cribs' drop sides can malfunction, detach or otherwise fail, causing part of the drop side to fall out of position, creating a space into which an infant or toddler can roll and become wedged or entrapped, which can lead to strangulation or suffocation.

• Jardine Enterprises

156,000 Million Dollar Baby drop-side cribs

CPSC and Million Dollar Baby have received 43 reports of drop side failures. There were eight reports of children being entrapped between the mattress and drop side resulting in three reports of bruises to the head or upper body. Additionally, three children fell out of the crib when the drop side failed but they were not injured.

• More on this recall

50,000 Simmons drop-side cribs

The cribs' drop sides can malfunction, detach or otherwise fail, causing part of the drop side to fall out of position, creating a space into which an infant or toddler can roll and become wedged or entrapped, which can lead to strangulation or suffocation. A child can also fall out of the crib. Drop-side incidents can also occur due to incorrect assembly and with age-related wear and tear. Style numbers are printed on a permanent label on the headboard.

• Simmons Juvenile Products Inc.

In the last five years more than nine million cribs have been recalled because of a potential hazard to children. Drop-side cribs are blamed for the deaths of 32 children since 2000, CPSC said.

Could crib bumpers be one step closer to being banned?

Crib bumpers, the pillow-like lining used to separate the sides of the crib with an infant’s head, may be one step closer to extinction due to beefed up safety guidelines by the U.S. Consumer Product Safety Commission (CPSC).

While the CPSC doesn't specifically discourage use of bumpers, it does recommend keeping all extraneous items out of cribs like stuffed animals, pillows and heavy quilts.

Plus, whether it was intended or not, bumpers are nowhere to be seen among the examples of safe cribs featured in the commission’s informational video online.

Crib bumper safety

The safety of crib bumpers has been a hotly debated topic over the last decade. Consumer advocacy groups and children’s safety organizations believe bumpers can cause suffocation, strangulation, or contribute to Sudden Infant Death Syndrome (SIDS).  However, the government has been slow to take a stand on the controversial crib accessory.

Still, the commission is not ignoring the subject of safe sleep areas for infants and young toddlers.

In December 2010, it unanimously approved new, stricter safety standards for all cribs; standards that had not been updated in thirty years.

Under the new guidelines, crib manufacturers must ensure mattress supports are stronger, the crib hardware is more durable, and the safety testing of their products is more rigorous.

The commission’s standards also stop the manufacture and sale of traditional drop-side cribs, which they warned parents about in May, 2010 and issued almost a dozen recalls for since 2005.

According to the commission, over seven million drop-side cribs were included in the recalls due to suffocation and strangulation hazards created by the drop side.

While these are steps in a positive direction, when (or if) the commission will address the possible safety hazards of crib bumpers is anyone’s guess.

Bumper ban

Illinois Attorney General Lisa Madigan has been calling for the end of crib bumpers since December 2010.

Last month, she urged the Juvenile Products Manufacturers Association (JPMA), the national industry trade group overseeing manufacturers of crib bumpers, to release the results of a study it conducted on the safety of bumpers.  As of mid-January 2011, the results have yet to be released.

Madigan continues to warn parents and care-givers of the potentially fatal risk of using crib bumpers.

Along with discouraging keeping bulky items out of cribs, the CPSC’s safety guidelines included other important tips to keep babies and young toddlers safe while they sleep:

• To prevent suffocation, never place pillows or thick quilts in a baby's sleep environment. Also, make sure there are no gaps larger than two fingers between the sides of the crib and the mattress.
• Proper assembly of cribs is paramount - Follow the instructions provided and make sure that every part is installed correctly. If you are not sure, call the manufacturer for assistance.
• Do not use cribs older than 10 years or broken or modified cribs. Infants can strangle to death if their bodies pass through gaps between loose components or broken slats while their heads remain entrapped.
• Set up play yards properly according to manufacturers' directions. Only use the mattress pad provided with the play yard; do not add extra padding.
• Never place a crib near a window with blind, curtain cords or baby monitor cords; babies can strangle on cords.

The commission also has resources for parents and care-givers to see if their child’s crib has been included in any of the recalls.

The cribs pose risks of strangulation, suffocation hardware linked to deaths and injuries

By James Limbach of ConsumerAffairs

The U.S. Consumer Product Safety Commission (CPSC) is warning consumers that "SafetyCraft" brand full-size and portable drop-side cribs manufactured or distributed by Generation 2 Worldwide contain drop-side hardware that appears to be identical to Generation 2 Worldwide ChildESIGNS brand drop-side cribs recalled in February 2010.

This hardware found on SafetyCraft drop-side cribs can fail and place infants and toddlers at risk of strangulation and suffocation. CPSC staff urges parents and caregivers to stop using these cribs immediately and find an alternative, safe sleeping environment for their baby. Do not attempt to fix these cribs.

Ownership change

Generation 2 Worldwide ceased operations in 2005. The "SafetyCraft" trademark was then purchased by Foundations Children's Products of Medina, OH. SafetyCraft cribs manufactured and sold by Foundations Children's Products are NOT the subject of this safety alert. Consumers can identify the Foundations SafetyCraft crib with "Foundations" printed on the mattress support assembly instructions label under the crib mattress.

Because Generation 2 Worldwide ceased operations, CPSC has limited information about these cribs and where they were sold. CPSC has been unable to identify major retailers that sold these cribs.

Identifying products

The name "SafetyCraft" appears on a label affixed to the crib's headboard or footboard. Product labels may identify the place of manufacture as Indonesia or Dothan, Alabama.

This warning involves all SafetyCraft drop-side cribs, including model 92-8112, manufactured and/or sold by Generation 2Worldwide. Some of the cribs have a clear plastic headboard and footboard. These cribs are in use in child care facilities as well as homes.

Danger to children

The crib's plastic drop-side hardware can break, which can cause the drop side of the crib to detach from a corner of the crib. When the drop side detaches, it creates a space into which an infant or toddler can roll and become wedged or entrapped.

When a child is trapped between the drop side and the crib mattress, it creates a risk of suffocation or strangulation. In addition, the crib's mattress support can detach from the crib frame, creating a hazardous space in which an infant or toddler can become entrapped and suffocate or strangle.

CPSC received reports of three infant suffocation deaths and 20 drop side-related incidents involving previously recalled models of Generation 2 Worldwide and ChildESIGNS cribs with plastic hardware similar to "SafetyCraft" cribs.

Parent advice

CPSC reminds parents not to use any crib with missing, broken, or loose parts. Make sure to tighten hardware from time to time to keep the crib sturdy. When using a drop-side crib, parents should check to make sure the drop-side or any other moving part operates smoothly.

Always check all sides and corners of the crib for disengagement. Any disengagement can create a gap and entrap a child. In addition, do not try to repair any side of the crib, especially with tape, wire or rope.

More information on crib safety can be found at CPSC's Crib Information Center.

Incident or injury reports that are either directly related to this product recall or involve a different hazard with the same product can be made here.

19-year study finds thousands of babies are injured or killed by their beds annually

When the United States Consumer Product Safety Commission (CPSC) announced a ban drop-side cribs in December 2010, after millions of these products had been recalled, many parents and caregivers of small children began to question the safety of cribs, playpens and bassinets.

A new study conducted by researchers at the Center for Injury Research and Policy of The Research Institute at Nationwide Children's Hospital examined injuries associated with cribs, playpens and bassinets among children younger than two years of age from 1990 through 2008.

What the found might upset even the most experienced parents.

During the 19-year study period, an average of 9,500 injuries and more than 100 deaths related to these products were seen in U.S. emergency departments each year.

According to the study, the majority of injuries – 83 percent -- involved cribs. The most common injury diagnosis was soft-tissue injury (34 percent), followed by concussion or head injury (21 percent).

The head or neck was the most frequently injured body region (40 percent), followed by the face (28 percent).

Two-thirds of the injuries were the result of a fall, and the percentage of injuries attributed to falls increased with age.

“Despite the attention given to crib safety over the past two decades, the number of injuries and deaths associated with these products remains unacceptably high,” said Dr. Gary Smith, MD, senior author of the study and director of the Center for Injury Research and Policy.

Smith, also a Professor of Pediatrics at The Ohio State University College of Medicine, said cribs, playpens and bassinets must be held to a higher standard than most baby products, which require parental supervision to maintain safety, because parents are expected to leave their child unattended in them and walk away with peace of mind.

“Educating caregivers about the proper use and potential dangers of these products is an important part of making cribs safer for children, but education alone is not enough,” said Smith. “Innovations in product design and manufacture can provide automatic protection that does not rely on actions of caregivers to keep children safe.”

In recent years, organizations such as the CPSC and the American Academy of Pediatrics have amplified their efforts to increase crib safety.

11 million recalls

The CPSC has issued recalls of more than 11 million cribs and has prohibited the manufacture, sale or lease of drop-side cribs starting in June 2011.

Continued strengthening and enforcement of crib safety standards will protect more young children from harm.

Despite the potential risks, cribs are still considered to be the safest location where parents can place infants to sleep. There are several steps parents and caregivers should take when selecting a crib for their child:

Pay close attention to the crib you select.

• Select a crib that meets all current safety standards, does not have a drop side and is not old, broken or modified.
• Avoid cribs with cutouts or decorative corner posts or knobs that stick up more than 1/16th of an inch
• Measure the slats to make sure they are not more than 2 and 3/8 inches apart
• Visit Recalls.gov to make sure the crib has not been recalled
• Make sure the mattress fits tightly into the crib. If you can fit more than two fingers between the mattress and the crib, you need a bigger mattress
• Frequently examine the crib to make sure it is in good repair and that there are no loose parts
• Carefully read and follow all assembly instructions

When putting your child in a crib to sleep, consider the following:

• Always place your baby on his or her back to sleep
• Remember that a bare crib is best. Do not add pillows, blankets, sleep positioners, stuffed animals or bumpers to the crib
• Crib tents and mesh canopies are not safe to use over cribs. Children can become trapped or strangle in them if they try to get out
• Avoid placing the crib near a window to prevent falls and possible strangulation from cords from window blinds or shades

Monitor your child's developmental milestones and make changes to the crib as needed.

• Once your child can push up on his hands and knees or is 5 months old (whichever occurs first), remove all mobiles and hanging toys
• When your child can pull herself up or stand, adjust the mattress to the lowest position. Having the crib sides at least 26 inches above the mattress can help prevent falls
• Check the manufacturer's instructions to know when your child will outgrow the crib. This generally occurs when your child reaches 35 inches in height

If using a bassinet or playpen, make sure they have a sturdy, wide base and that your child meets all height and weight limits.

Smith’s study will be released online on February 21 will appear in the March 2011 print issue of Pediatrics.

The crib's tubular metal mattress-support frame can bend or detach and cause part of the mattress to collapse, creating a space into which an infant or toddler can roll and become wedged, entrapped or fall out of the crib.

          









      

CPSC has received a report of a one-year-old child from North Attleboro, Mass. who suffocated when he became entrapped between the crib mattress and the crib frame in April 2008. CPSC is aware of 13 additional incidents involving the recalled cribs collapsing due to the metal mattress-support frame bending or detaching, including one child entrapment that did not result in injury, and one child who suffered minor cuts to his head when his mattress collapsed and he fell out of the crib.

CPSC staff urges parents and caregivers to stop using these cribs immediately and find an alternative, safe sleeping environment for their baby. Do not attempt to fix these cribs.

Due to the fact that Simplicity and its successor, SFCA Inc., are no longer in business, CPSC has limited information about the number of cribs sold.

All Simplicity drop-side cribs have previously been recalled for a hazard involving the drop side. Simplicity drop-side cribs could still be in use by parents or caregivers who are unaware of the recalls or by those who received a repair kit to immobilize the drop side from Simplicity when the firm was still in business. This recall involves all Simplicity cribs with tubular metal mattress-support frames, which include but are not limited to the following models:

Some model numbers are followed by letters, indicating the color or finish of the crib. The name "Simplicity Inc." or "Simplicity for Children" appears on a label on the crib's mattress-support frame and/or the crib's end panels. The cribs were manufactured in China.

The recalled cribs were sold at Walmart, Target, Babies R Us and other stores nationwide for between $150 and $300. Consumers should contact the store where the crib was purchased to receive a refund, replacement crib or store credit.

Warning

CPSC would like to remind parents not to use any crib with missing, broken or loose parts. Make sure to tighten hardware from time to time to keep the crib sturdy. When using a drop-side crib, parents should check to make sure the drop side or any other moving part operates smoothly. Always check all sides and corners of the crib for disengagement. Any disengagement can create a gap, which could fatally entrap a child. In addition, do not try to repair any side of the crib with tape, wire, rope or by other means. Infants and toddlers have died in cribs with makeshift repairs.

For more information on Crib Safety, visit CPSC's Crib Information Center.

The recall is being conducted in cooperation with the U.S. Consumer Product Safety Commission (CPSC).

More than 9 million dangerous cribs recalled since 2005

By Mark Huffman of ConsumerAffairs

After high-profile recalls of drop-side cribs that can suffocate infants, the Consumer Product Safety Commission has expanded its recall to include two million cribs made by seven companies.

The beds included in the recall were made by Child Craft, Delta Enterprises Corp., Evenflo, Jardine Enterprises, LaJobi, More on this recall and Simmons Juvenile Products Inc.

Some, but not all, are the drop-side cribs, which pose a danger to infants who become trapped in the gap between the mattress and the side of the crib. Included in this latest recall is the Child Craft brand "Crib 'N' Double Bed" full size stationary-side crib with dowel.

The crib's stationary side can be assembled upside-down but still appears to be assembled correctly. If assembled upside-down, the crib side contains a hazardous five-inch gap at the top of the crib. Infants or toddlers can become entrapped in this gap, which can lead to entrapment, strangulation or other injuries.

CPSC has received four reports of children becoming entrapped between the dowel and the crib's stationary front side. In two of those reports, the child was trapped by his/her head and was in danger of being strangled. In the other two reports, the child was trapped by his/her arm. This hazard can occur on both the front and back sides of the crib, the agency said.

Listed below are cribs included in the latest recall.

747,000 Delta drop-side cribs

Improper installation can cause the mattress platform to collapse.

This recall involves Delta drop-side cribs with three different types of drop-side hardware and Delta cribs with wooden stabilizer bars that support the mattress platform.

• Delta Enterprises Corp.

750,000 Jenny Lind drop-side cribs distributed by Evenflo

CPSC and Evenflo have received 31 reports of drop sides that malfunctioned or detached. One involved the entrapment of a seven-month-old boy between the drop side and the crib mattress. He sustained bumps and bruises to his head. Nine children fell out of the crib when the drop side detached, unlocked or fell off. Seven of those children sustained minor injuries, including bumps, bruises and cuts. Fourteen other incidents involved no injuries. In addition, CPSC has received two reports of children who became entrapped when the mattress support detached in one corner of cribs manufactured between 2000 and 2004.

• More on this recall

306,000 Bonavita, Babi Italia and ISSI drop-side cribs manufactured by LaJobi

This recall involves all models of Bonavita, Babi Italia and ISSI drop-side cribs manufactured by LaJobi. The cribs have drop-side hardware that contains metal or plastic pegs that are recessed into either the drop side or the headboard and footboard of the crib. A label on the headboard of the crib identifies the manufacturer as LaJobi.

• LaJobi

130,000 Jardine drop-side cribs imported by Toys R Us

The cribs' drop sides can malfunction, detach or otherwise fail, causing part of the drop side to fall out of position, creating a space into which an infant or toddler can roll and become wedged or entrapped, which can lead to strangulation or suffocation.

• Jardine Enterprises

156,000 Million Dollar Baby drop-side cribs

CPSC and Million Dollar Baby have received 43 reports of drop side failures. There were eight reports of children being entrapped between the mattress and drop side resulting in three reports of bruises to the head or upper body. Additionally, three children fell out of the crib when the drop side failed but they were not injured.

• More on this recall

50,000 Simmons drop-side cribs

The cribs' drop sides can malfunction, detach or otherwise fail, causing part of the drop side to fall out of position, creating a space into which an infant or toddler can roll and become wedged or entrapped, which can lead to strangulation or suffocation. A child can also fall out of the crib. Drop-side incidents can also occur due to incorrect assembly and with age-related wear and tear. Style numbers are printed on a permanent label on the headboard.

• Simmons Juvenile Products Inc.

In the last five years more than nine million cribs have been recalled because of a potential hazard to children. Drop-side cribs are blamed for the deaths of 32 children since 2000, CPSC said.

The cribs drop sides can malfunction, detach or otherwise fail, causing part of the drop side to fall out of position, creating a space into which an infant or toddler can roll and become wedged or entrapped, which can lead to strangulation or suffocation. A child can also fall out of the crib. Drop-side incidents can also occur due to incorrect assembly and with age-related wear and tear.

Incidents/Injuries: CPSC and Evenflo have received 31 reports of drop sides that malfunctioned or detached. One involved the entrapment of a seven month old boy between the drop side and the crib mattress. He sustained bumps and bruises to his head. Nine children fell out of the crib when the drop side detached, unlocked or fell off. Seven of those children sustained minor injuries, including bumps, bruises and cuts. Fourteen other incidents involved no injuries.

In addition, CPSC has received two reports of children who became entrapped when the mattress support detached in one corner of cribs manufactured between 2000 and 2004.

The following Evenflo crib models are included in this recall. The model number is located on a label on the bottom beam of the headboard.

The cribs, made in Mexico and China, were sold at childrens product stores and various other retailers nationwide from January 2000 through November 2007 for about $200.

Consumers should immediately stop using the recalled drop-side cribs and contact Evenflo to receive a free repair kit that will immobilize the drop side. A repair kit for the mattress support system is also available for cribs with model numbers starting with 012 and 014 that were manufactured between 2000 and 2004. In the meantime, find an alternate, safe sleep environment for the child, such as a bassinet, play yard or toddler bed depending on the childs age. The repair kits will be provided to consumers within the next several weeks.

For additional information, contact Evenflo at (800) 356-2229 between 8 a.m. and 5 p.m. ET Monday through Friday or visit the firms web site at http://safety.evenflo.com

Cautionary note

Federal safety regulators remind parents not to use any crib with missing, broken, or loose parts. Make sure to tighten hardware from time to time to keep the crib sturdy. When using a drop-side crib, parents should check to make sure the drop side or any other moving part operates smoothly. Always check all sides and corners of the crib for disengagement. Disengagements can create a gap and entrap a child.

In addition, parents should not try to repair any side of the crib. Babies have died in cribs where repairs were attempted by caregivers. Age is a factor in the safety of any crib. At a minimum, CPSC staff recommends that you not use a crib that is older than 10 years. Many older cribs may not meet current voluntary standards and can have numerous safety problems.

The recall is being conducted in cooperation with the U.S. Consumer Product Safety Commission (CPSC).

Missing Safety Pegs Create Risk of Entrapment and Suffocation

By Truman Lewis of ConsumerAffairs

The U.S. Consumer Product Safety Commission (CPSC) is repeating the 2008 recall of more than 985,000 drop-side cribs with "Crib Trigger Lock and Safety Peg" hardware.

In January 2011, CPSC and Delta Enterprise Corp., the crib's manufacturer, learned of a 2009 death in which a 7-month-old girl from Colorado Springs, Colo., became entrapped and suffocated between the detached drop-side and mattress of her recalled crib. The crib was purchased secondhand and re-assembled without safety pegs in the bottom tracks.

Missing safety pegs can create a situation where the crib's drop-side rail disengages from the track. This can create a hazardous space in which an infant can become entrapped and suffocate.

At the time of the October 2008 recall, CPSC notified consumers about the death of an 8-month-old girl who became entrapped and suffocated when the drop side of the crib detached. The crib involved in this incident also was re-assembled without safety pegs. At the time of the October 2008 recall announcement, there were reports of two entrapments and nine detachments in cribs without safety pegs.

"Buying or accepting cribs second hand can be risky," said CPSC Chairman Inez Tenenbaum. "Second hand cribs may not come with all of the necessary parts that are needed to make sure your baby is safe. We urge parents and caregivers to use caution and to be aware that new rules established by CPSC will bring safer cribs to the market this summer."

The repeated recall involves cribs that were made in Taiwan and Indonesia. The cribs were sold at major retail stores including Kmart, Target and Walmart between January 1995 and December 2005 (through September 2007 for model 4624) for about $100.

Delta's name and address is printed on the mattress support boards and the Delta logo is on the crib's top teether rail. Model numbers are located on the top of the mattress support board. This announcement includes the following 49 crib models with "Crib Trigger Lock with Safety Peg" drop-side hardware:

• 4320, 4340;
• 4500, 4520, 4530, 4532, 4540, 4542, 4550, 4551, 4580;
• 4600, 4620, 4624 - production dates 01/06 thru 11/07, 4640, 4660, 4720, 4735, 4742, 4750 - production dates 01/95 thru 12/00;
• 4760, 4770, 4780, 4790;
• 4820, 4840, 4850, 4860, 4880, 4890, 4892; and
• 4900, 4910, 4920, 4925-2, 4925-6, 4930, 4940, 4943, 4944, 4947, 4948, 4949, 4950, 4958, 4963, 4968, 4969, 4980.

CPSC urges parents and caregivers to immediately stop using cribs that are missing a safety peg on either leg of the drop side and contact Delta to receive a free, easy-to-install repair kit. Call Delta toll-free at (800) 816-5304 anytime or visit the firm's website at www.cribrecallcenter.com to order the free repair kit.

Parents and caregivers are encouraged to find a safe, alternative sleep environment for their child until the repair kit, with new safety pegs, is safely installed on the recalled cribs.

CPSC reminds parents not to use any crib with missing, broken or loose parts. Make sure to tighten hardware from time to time to keep the crib sturdy. When using a drop-side crib, parents should check to make sure the drop side or any other moving part operates smoothly. Always check all sides and corners of the crib for parts separating that can create a gap and entrap a child.

In addition, do not try to repair any side of the crib. Babies have died in cribs where repairs were attempted by caregivers. Crib age is a factor in safety. At a minimum, CPSC staff recommends that you do not use a crib that is older than 10 years old. New, mandatory federal crib rules take effect on June 28, 2011. All cribs manufactured and sold after that date must meet new and improved safety requirements. Older cribs do not meet the new standard and can have a variety of safety problems.

U.S. hadn't updated crib safety standards for 30 years

By James R. Hood of ConsumerAffairs

Setting aside objections from retailers and manufacturers, the U.S. Consumer Product Safety Commission is implementing new safety standards for baby cribs later this month.

Effective June 28, anyone who manufactures or sells cribs will be required to meet the new standards, although day care centers, crib rental companies and hotels will have until December 28, 2012 to update their cribs.

“I am very pleased that the new mandatory crib standards will stop the manufacture and sale of dangerous traditional drop-side cribs and will vastly improve the structural integrity of cribs,” said CPSC chair Inez M. Tenenbaum, noting that crib safety standards have not been updated in nearly 30 years.

Detaching drop-side rails were associated with at least 32 infant suffocation and strangulation deaths since 2000, according to the CPSC. Additional deaths have occurred due to faulty or defective hardware.

Manufacturers and retailers had objected that the new rules would cause an economic hardship, particularly on smaller stores but the commission voted 3-2 to impose the new standards on schedule.

The new standards will:

1. stop the manufacture and sale of dangerous, traditional drop-side cribs;

2. make mattress supports stronger;

3. improve slat strength,

4. make crib hardware more durable; and

5. make safety testing more rigorous.

The standards aim to keep children safer in their cribs and prevent deaths resulting from detaching crib drop-sides and faulty or defective hardware. The tougher standards were mandated by the Consumer Product Safety Improvement Act of 2008.

Tenenbaum said the commission granted the delays to child care centers, crib rental stores and hotels and motels were necessary not only to minimize the economic impact but also to prevent shortages of new cribs. She estimated that replacing all of the cribs already in use at such locations would create a demand of approximately 935,000 cribs, which would amount to nearly $467 million in replacement costs.

“In order to ensure sufficient availability of compliant cribs and ensure an orderly and successful transition to the use of complaint cribs by child care providers and places of public accommodation, the Commission adopted a two-step phase in of the rule,” Tenenbaum said.

Retailers unhappy

Any cribs not meeting the current standard must be destroyed if they’re not sold by June 28. Industry estimates put the number of unsold cribs between 10,000 and 20,000. Some retailers, hoping to clear out their stock, have offered steep discounts to consumers.

“Overregulation is going to lead to the destroying of thousands of cribs that are perfectly good — many that are better than what will come out after the new regulations,” Gene Francis, a South Dakota-based retailer and member of the National Independent Nursery Furniture Retailers Association, told Kids Today.

But Commissioner Thomas Moore showed little sympathy for that argument.

"We expect companies to comply with the Commission’s rules," he said. "It appears that the vast majority of retailers did plan and are ready to comply by the June 28th date.  In a rule of this magnitude, it is expected that there will be 
some market disruption and that some companies will experience economic loss."

Moore said it was impractical to ask the CPSC to allow retailers to continue selling cribs that do not meet the new standard.

"There is little that we know about the noncomplying cribs these retailers want to sell or about the reasons the retailers find themselves with noncompliant inventory.  However, there is much that we don’t know.  When were these cribs made?  Who made them and where?  Who tested them and when?  What standard were they tested to?  When were they ordered?  Did the quantity ordered take into account the looming effective date of the new crib standards?"

"Were retailers buying imported noncomplying cribs at fire sale prices to try to make a profit before they had to start buying more expensive cribs that met the new standards?" Moore asked.  "Will retrofit kits be available to bring the cribs into compliance?  We simply do not know."

The crib's tubular metal mattress-support frame can bend or detach and cause part of the mattress to collapse, creating a space into which an infant or toddler can roll and become wedged, entrapped or fall out of the crib.

          









      

CPSC has received a report of a one-year-old child from North Attleboro, Mass. who suffocated when he became entrapped between the crib mattress and the crib frame in April 2008. CPSC is aware of 13 additional incidents involving the recalled cribs collapsing due to the metal mattress-support frame bending or detaching, including one child entrapment that did not result in injury, and one child who suffered minor cuts to his head when his mattress collapsed and he fell out of the crib.

CPSC staff urges parents and caregivers to stop using these cribs immediately and find an alternative, safe sleeping environment for their baby. Do not attempt to fix these cribs.

Due to the fact that Simplicity and its successor, SFCA Inc., are no longer in business, CPSC has limited information about the number of cribs sold.

All Simplicity drop-side cribs have previously been recalled for a hazard involving the drop side. Simplicity drop-side cribs could still be in use by parents or caregivers who are unaware of the recalls or by those who received a repair kit to immobilize the drop side from Simplicity when the firm was still in business. This recall involves all Simplicity cribs with tubular metal mattress-support frames, which include but are not limited to the following models:

Some model numbers are followed by letters, indicating the color or finish of the crib. The name "Simplicity Inc." or "Simplicity for Children" appears on a label on the crib's mattress-support frame and/or the crib's end panels. The cribs were manufactured in China.

The recalled cribs were sold at Walmart, Target, Babies R Us and other stores nationwide for between $150 and $300. Consumers should contact the store where the crib was purchased to receive a refund, replacement crib or store credit.

Warning

CPSC would like to remind parents not to use any crib with missing, broken or loose parts. Make sure to tighten hardware from time to time to keep the crib sturdy. When using a drop-side crib, parents should check to make sure the drop side or any other moving part operates smoothly. Always check all sides and corners of the crib for disengagement. Any disengagement can create a gap, which could fatally entrap a child. In addition, do not try to repair any side of the crib with tape, wire, rope or by other means. Infants and toddlers have died in cribs with makeshift repairs.

For more information on Crib Safety, visit CPSC's Crib Information Center.

The recall is being conducted in cooperation with the U.S. Consumer Product Safety Commission (CPSC).

More than 9 million dangerous cribs recalled since 2005

By Mark Huffman of ConsumerAffairs

After high-profile recalls of drop-side cribs that can suffocate infants, the Consumer Product Safety Commission has expanded its recall to include two million cribs made by seven companies.

The beds included in the recall were made by Child Craft, Delta Enterprises Corp., Evenflo, Jardine Enterprises, LaJobi, More on this recall and Simmons Juvenile Products Inc.

Some, but not all, are the drop-side cribs, which pose a danger to infants who become trapped in the gap between the mattress and the side of the crib. Included in this latest recall is the Child Craft brand "Crib 'N' Double Bed" full size stationary-side crib with dowel.

The crib's stationary side can be assembled upside-down but still appears to be assembled correctly. If assembled upside-down, the crib side contains a hazardous five-inch gap at the top of the crib. Infants or toddlers can become entrapped in this gap, which can lead to entrapment, strangulation or other injuries.

CPSC has received four reports of children becoming entrapped between the dowel and the crib's stationary front side. In two of those reports, the child was trapped by his/her head and was in danger of being strangled. In the other two reports, the child was trapped by his/her arm. This hazard can occur on both the front and back sides of the crib, the agency said.

Listed below are cribs included in the latest recall.

747,000 Delta drop-side cribs

Improper installation can cause the mattress platform to collapse.

This recall involves Delta drop-side cribs with three different types of drop-side hardware and Delta cribs with wooden stabilizer bars that support the mattress platform.

• Delta Enterprises Corp.

750,000 Jenny Lind drop-side cribs distributed by Evenflo

CPSC and Evenflo have received 31 reports of drop sides that malfunctioned or detached. One involved the entrapment of a seven-month-old boy between the drop side and the crib mattress. He sustained bumps and bruises to his head. Nine children fell out of the crib when the drop side detached, unlocked or fell off. Seven of those children sustained minor injuries, including bumps, bruises and cuts. Fourteen other incidents involved no injuries. In addition, CPSC has received two reports of children who became entrapped when the mattress support detached in one corner of cribs manufactured between 2000 and 2004.

• More on this recall

306,000 Bonavita, Babi Italia and ISSI drop-side cribs manufactured by LaJobi

This recall involves all models of Bonavita, Babi Italia and ISSI drop-side cribs manufactured by LaJobi. The cribs have drop-side hardware that contains metal or plastic pegs that are recessed into either the drop side or the headboard and footboard of the crib. A label on the headboard of the crib identifies the manufacturer as LaJobi.

• LaJobi

130,000 Jardine drop-side cribs imported by Toys R Us

The cribs' drop sides can malfunction, detach or otherwise fail, causing part of the drop side to fall out of position, creating a space into which an infant or toddler can roll and become wedged or entrapped, which can lead to strangulation or suffocation.

• Jardine Enterprises

156,000 Million Dollar Baby drop-side cribs

CPSC and Million Dollar Baby have received 43 reports of drop side failures. There were eight reports of children being entrapped between the mattress and drop side resulting in three reports of bruises to the head or upper body. Additionally, three children fell out of the crib when the drop side failed but they were not injured.

• More on this recall

50,000 Simmons drop-side cribs

The cribs' drop sides can malfunction, detach or otherwise fail, causing part of the drop side to fall out of position, creating a space into which an infant or toddler can roll and become wedged or entrapped, which can lead to strangulation or suffocation. A child can also fall out of the crib. Drop-side incidents can also occur due to incorrect assembly and with age-related wear and tear. Style numbers are printed on a permanent label on the headboard.

• Simmons Juvenile Products Inc.

In the last five years more than nine million cribs have been recalled because of a potential hazard to children. Drop-side cribs are blamed for the deaths of 32 children since 2000, CPSC said.

The cribs drop sides can malfunction, detach or otherwise fail, causing part of the drop side to fall out of position, creating a space into which an infant or toddler can roll and become wedged or entrapped, which can lead to strangulation or suffocation. A child can also fall out of the crib. Drop-side incidents can also occur due to incorrect assembly and with age-related wear and tear.

Incidents/Injuries: CPSC and Evenflo have received 31 reports of drop sides that malfunctioned or detached. One involved the entrapment of a seven month old boy between the drop side and the crib mattress. He sustained bumps and bruises to his head. Nine children fell out of the crib when the drop side detached, unlocked or fell off. Seven of those children sustained minor injuries, including bumps, bruises and cuts. Fourteen other incidents involved no injuries.

In addition, CPSC has received two reports of children who became entrapped when the mattress support detached in one corner of cribs manufactured between 2000 and 2004.

The following Evenflo crib models are included in this recall. The model number is located on a label on the bottom beam of the headboard.

The cribs, made in Mexico and China, were sold at childrens product stores and various other retailers nationwide from January 2000 through November 2007 for about $200.

Consumers should immediately stop using the recalled drop-side cribs and contact Evenflo to receive a free repair kit that will immobilize the drop side. A repair kit for the mattress support system is also available for cribs with model numbers starting with 012 and 014 that were manufactured between 2000 and 2004. In the meantime, find an alternate, safe sleep environment for the child, such as a bassinet, play yard or toddler bed depending on the childs age. The repair kits will be provided to consumers within the next several weeks.

For additional information, contact Evenflo at (800) 356-2229 between 8 a.m. and 5 p.m. ET Monday through Friday or visit the firms web site at http://safety.evenflo.com

Cautionary note

Federal safety regulators remind parents not to use any crib with missing, broken, or loose parts. Make sure to tighten hardware from time to time to keep the crib sturdy. When using a drop-side crib, parents should check to make sure the drop side or any other moving part operates smoothly. Always check all sides and corners of the crib for disengagement. Disengagements can create a gap and entrap a child.

In addition, parents should not try to repair any side of the crib. Babies have died in cribs where repairs were attempted by caregivers. Age is a factor in the safety of any crib. At a minimum, CPSC staff recommends that you not use a crib that is older than 10 years. Many older cribs may not meet current voluntary standards and can have numerous safety problems.

The recall is being conducted in cooperation with the U.S. Consumer Product Safety Commission (CPSC).

Missing Safety Pegs Create Risk of Entrapment and Suffocation

By Truman Lewis of ConsumerAffairs

The U.S. Consumer Product Safety Commission (CPSC) is repeating the 2008 recall of more than 985,000 drop-side cribs with "Crib Trigger Lock and Safety Peg" hardware.

In January 2011, CPSC and Delta Enterprise Corp., the crib's manufacturer, learned of a 2009 death in which a 7-month-old girl from Colorado Springs, Colo., became entrapped and suffocated between the detached drop-side and mattress of her recalled crib. The crib was purchased secondhand and re-assembled without safety pegs in the bottom tracks.

Missing safety pegs can create a situation where the crib's drop-side rail disengages from the track. This can create a hazardous space in which an infant can become entrapped and suffocate.

At the time of the October 2008 recall, CPSC notified consumers about the death of an 8-month-old girl who became entrapped and suffocated when the drop side of the crib detached. The crib involved in this incident also was re-assembled without safety pegs. At the time of the October 2008 recall announcement, there were reports of two entrapments and nine detachments in cribs without safety pegs.

"Buying or accepting cribs second hand can be risky," said CPSC Chairman Inez Tenenbaum. "Second hand cribs may not come with all of the necessary parts that are needed to make sure your baby is safe. We urge parents and caregivers to use caution and to be aware that new rules established by CPSC will bring safer cribs to the market this summer."

The repeated recall involves cribs that were made in Taiwan and Indonesia. The cribs were sold at major retail stores including Kmart, Target and Walmart between January 1995 and December 2005 (through September 2007 for model 4624) for about $100.

Delta's name and address is printed on the mattress support boards and the Delta logo is on the crib's top teether rail. Model numbers are located on the top of the mattress support board. This announcement includes the following 49 crib models with "Crib Trigger Lock with Safety Peg" drop-side hardware:

• 4320, 4340;
• 4500, 4520, 4530, 4532, 4540, 4542, 4550, 4551, 4580;
• 4600, 4620, 4624 - production dates 01/06 thru 11/07, 4640, 4660, 4720, 4735, 4742, 4750 - production dates 01/95 thru 12/00;
• 4760, 4770, 4780, 4790;
• 4820, 4840, 4850, 4860, 4880, 4890, 4892; and
• 4900, 4910, 4920, 4925-2, 4925-6, 4930, 4940, 4943, 4944, 4947, 4948, 4949, 4950, 4958, 4963, 4968, 4969, 4980.

CPSC urges parents and caregivers to immediately stop using cribs that are missing a safety peg on either leg of the drop side and contact Delta to receive a free, easy-to-install repair kit. Call Delta toll-free at (800) 816-5304 anytime or visit the firm's website at www.cribrecallcenter.com to order the free repair kit.

Parents and caregivers are encouraged to find a safe, alternative sleep environment for their child until the repair kit, with new safety pegs, is safely installed on the recalled cribs.

CPSC reminds parents not to use any crib with missing, broken or loose parts. Make sure to tighten hardware from time to time to keep the crib sturdy. When using a drop-side crib, parents should check to make sure the drop side or any other moving part operates smoothly. Always check all sides and corners of the crib for parts separating that can create a gap and entrap a child.

In addition, do not try to repair any side of the crib. Babies have died in cribs where repairs were attempted by caregivers. Crib age is a factor in safety. At a minimum, CPSC staff recommends that you do not use a crib that is older than 10 years old. New, mandatory federal crib rules take effect on June 28, 2011. All cribs manufactured and sold after that date must meet new and improved safety requirements. Older cribs do not meet the new standard and can have a variety of safety problems.